How Long Does It Take to Install a Toilet?

How Long Does It Take to Install a Toilet

The time it takes to install a toilet depends on the type of toilet you have. If you have a standard gravity-fed toilet, it should only take a few minutes to install.

However, if you have a pressure-assisted or dual flush toilet, it may take a bit longer.

In general, though, most toilets can be installed in about 30 minutes or so.

Toilet installation is generally not a difficult task, but there are a few things you need to keep in mind.

First, make sure you have all the necessary tools and supplies before you start.

Second, follow the instructions that came with your toilet carefully.

Finally, take your time and be careful – rushing through the installation process could result in a failure output.

Toilets installation process

There are a few things that need to be considered before starting the installation process which are:

  • Making sure that all the necessary tools and supplies are available.
  • Following the instructions given in the manual carefully.
  • Taking enough time and being careful while doing it.

Further, it is better to follow the instructions given in the manual to avoid any kind of mistakes.

The tools you will need for installing a toilet

The most common tools you need in installing a toilet are a hacksaw, a putty knife, an adjustable wrench, a rubber mallet, and a screwdriver.

You will also need some supplies like plumbers’ putty, Teflon tape, and a wax ring with a flange.

How to remove the old toilet?

Removing an old toilet is a simple process.

The first step is to turn off the water supply to the toilet.

Then, flush the toilet to empty the tank.

Next, disconnect the supply line from the shut-off valve and remove it from the tank. Use a hacksaw to cut through the bolts that secure the toilet to the floor flange.

You may need to use a putty knife to break the seal between the toilet and the floor.

Finally, lift the toilet from the floor and remove any remaining putty or wax from the flange.

How to install the new toilet?

The first step in installing a new toilet is to place a new wax ring on the flange.

Next, set the new toilet in place and press down gently to seat the wax ring. Use a rubber mallet to tap the toilet into place if necessary.

Then, connect the supply line to the shut-off valve and turn on the water supply.

Finally, install the bolts and tighten them with an adjustable wrench.

You may need to adjust the height of the toilet by turning the bolts at the base of the toilet.

Once the toilet is installed, test it by flushing it a few times to make sure it is working properly.

Installing a toilet is not a difficult task but still, it is better to be careful while doing it.

Make sure that you have all the necessary tools and supplies before starting the installation process.

Also, follow the instructions given in the manual carefully to avoid any mistakes.

Adjusting the water level and flushing mechanism

After the toilet is installed, you may need to adjust the water level in the tank.

The water level should be set so that the float is about 1 inch below the rim of the tank.

You can also adjust the flushing mechanism to control how much water is used for each flush.

Most toilets have a knob or lever that controls the amount of water that is released into the bowl.

If your toilet is constantly running, you may need to adjust the float or the flushing mechanism to stop the water from running constantly.

If you are not sure how to adjust the water level or the flushing mechanism, you can consult the manual that came with your toilet.

Or, you can contact a plumber for help.


In summary, installing a new toilet doesn’t have to be a daunting task.

By following the instructions carefully and having all of the necessary tools on hand, you can install your new toilet in just a few minutes.

If you’re not sure how to adjust the water level or the flushing mechanism, don’t worry.

The instructions that come with your toilet should tell you everything you need to know.

And if you still have questions, don’t hesitate to contact a plumber for help.

Greg Llama

Greg Llama is professional plummer and a family man. He shares his plumming experience on, a website dedicated to help people deal with common toilet problems.

Recent Posts